Reference: 23-001

Power supply 12 VDC / 2.1 A

Mean Well S-25-12 power supply 230 VAC to 12 VDC, 2.1 A Switching power supply with 12 V 2.1 A out, adjustable output voltage via potentiometer. Required for those who intend to connect many M-bus meters to our M-Bus Master, but also for those who want to connect sensors that require more power than the Logger 3030 can deliver on their analogue outputs...

Reference: 05-003

Pressure Sensor 0-2 Bar

LONN-2SX Pressure transmitter 0-2 bar, 4-20 mA. The sensor is widely used in many different areas, such as various applications in both real estate, homeowners, industry and HVAC. The pressure sensor is small, lightweight and made of stainless steel ( EN 1.4301, AISI 304), o-ring seals makes it resistant to water IP 66

Reference: 01-022

Brand: Energibutiken, WebIQ AB

SDM630 Modbus MCT V2 MID 3-phase electricity meter

SDM630 Modbus MCT V2 3-phase energy meter. MID-approved, for use with current transformators (Coils) 50 A and up. We stock 50, 100 and 200 A coils. Modular device for DIN rail 35mm, width: 4 modules, the display shows Volt, Amps, Power, Power factor and more. With pulse output suitable for logging, modbus RTU communication available suitable for our...

Reference: 03-012

Brand: Energibutiken, WebIQ AB

Extern onewire 4x20 oled-display

External onewire 4x20 oled display NOTE: Yellow characters. External display for Logger 1010 and Logger 3030 PRO Modbus, can be placed in any place e.g. kitchen, office, living room or similar. OLED means that the display exudes quality and has a very good sharpness and contrast. The display has controls US2066 and can also be used with Rasberiy PI,...

Reference: 03-037

White casing for 1-wire OLED display NHD-0420CW-AW3

White casing for 1-wire OLED display NHD-0420CW-AW3 This casing is 3D-printed and the finish is not perfect fur to that fact. Fits our 1-wire OLED display and can connect to Logger 1010 and Logger 3030. Size: 113 x 52 x 27 mm

Reference: 03-036

Black casing for 1-wire OLED display NHD-0420CW-AW3

Black casing for 1-wire OLED display NHD-0420CW-AW3 This casing is 3D-printed and the finish is not perfect fur to that fact. Fits our 1-wire OLED display and can connect to Logger 1010 and Logger 3030. Size: 113 x 52 x 27 mm

Reference: 01-029

Brand: Eastron

Eastron SDM630 MCT M-bus V2 MID 3-phase electricity meter

SDM630 MCT M-bus V2 MID 3-phase energy meter. Modular device for DIN rail 35mm, width: 4 modules, the display shows Volt, Amps, Power, Power factor and more. With pulse output suitable for logging, M-bus communication available suitable for our Logger 3030 datalogger. MID certification makes it possible to use for billing purposes.

Reference: 01-007

Brand: Energibutiken, WebIQ AB

SDM630 M-bus MID 3-phase electricity meter

SDM630 Mbus MID 3-phase energy meter. Modular device for DIN rail 35mm, width: 4 modules, the display shows Volt, Amps, Power, Power factor and more. With pulse output suitable for logging, Mbus RTU communication available suitable for our Logger 1010 datalogger. MID certification makes it possible to use for billing purposes.

Reference: 29-001

BRIDGE LR LoRa-brygga för trådlös modbus upp till 3 km

PickData LoRa Bridge for Modbus Wireless is used for reading wireless bus units. Perfect when, for example, electricity meters in different buildings need to be read off and it is difficult to pull cable.

Reference: 02-051

Brand: Energibutiken, WebIQ AB

Temperature - Humidity - Light-sensor module THLIQ-01

Temp / Humidity / Light Module THLIQ-01 High quality module with built-in temperature, humidity and light sensor, based on temp / humidifier HTU21D. Fits Logger 3030, 3030 PRO Modbus and Loggar 2020

Reference: 02-053

Brand: Energibutiken, WebIQ AB

PT1000 Universal temp sensor 6 mm 3 meter

PT1000 sensor, max 200°C, 3 meter 6 X 50 mm 3-wire universal temperature sensor.Suitable for measurement of all media that does not get more than 200°C hot.

Reference: 02-049

Brand: Energibutiken, WebIQ AB

PT100 Universal temp sensor 6 mm, 10 meter BK

PT100 sensor, max 200°C, 10 meter 6 X 50 mm 3-wire universal temperature sensor suitable for (among others) Logger 2020's high temp module HTMIQSuitable for measurement of all media that does not get more than 200°C hot. Note this model cannot be connected to the Logger 3030.

Reference: 04-016

Modul Modbus med 8 analoga ingångar

Modbus module with 8 analog inputs 8 channels of analog type: 0-20mA / 4-20mA DC, with 12bit AD chip With RS485 MODBUS RTU. Can be combined with industrial configuration software, PLC and touchpad Communication circuit is thunderstorm and interference protected. Works for Logger 3030 PRO Mobus.

Reference: 09-004

Brand: Energibutiken, WebIQ AB

Miljömodul

Environmental module Can be connected to two of our loggers, Logger 1010 or Logger 3030. Up to nine different environmental measurements!

Reference: 02-061

Brand: Energibutiken, WebIQ AB

PT1000 high temp sensor 6 mm 400°C 3 meter

PT1000 High temp sensor -50 to +200°C 3-wire universal high temp temperature sensor suitable for Logger 2020's high temp module HTMIQSuitable for measurement of all media that does not get more than 400° C hot. This sensor can also replace sensors such as Danfoss ESMB-12

Reference: 03-033

Power Supply for Logger 1010 & 3030

Power supply 12 VDC 1 A Power supply suitable for Logger 2020, Logger 3030 and our M-bus Converter Plug-in, switching, stabilized output voltage. Wide input voltage range

Reference: 03-032

Power Supply for Logger 1010 & 3030

Power supply 12 VDC 1 A Power supply suitable for Logger 2020, Logger 3030 and our M-bus Converter Plug-in, switching, stabilized output voltage. Wide input voltage range

Reference: 07-010

Temp pocket for ventilation

Temp pocket for ventilation This product is perfect for PT100, PT1000 and DALLAS 1-WIRE only for 6 mm enclosures. The temp pocket must be able to be installed in existing ventilation ducts in order to be able to measure temperatures in that part of the ventilation system.

Reference: 04-022

Heat conductive paste 3 grams

Heat conductive paste 3 grams This paste is great to use when installing a temp sensor to pipes, tanks or in temp pockets. A small amount of paste is enough to improve the measurement accuracy, particularly in terms of reaction times during sudden temperature changes.

Reference: 02-062

PT1000 to Modbus (RS485) Modul

Reference: 02-063

Modbus/PT1000 modul + 4 Digitala in.

Reference: 04-023

Heat conductive paste 20 grams

Heat conductive paste 20 grams This paste is great to use when installing a temp sensor to pipes, tanks or in temp pockets. A small amount of paste is enough to improve the measurement accuracy, particularly in terms of reaction times during sudden temperature changes.

Reference: 13-005

Connection Kit DN15

Connection Kit DN15 Used when connecting heat meters and/or water meters. Converts 3/4" straight thread to 1/2" tapered thread Kit includes 2 pcs with gaskets.

Reference: 02-003

Brand: Energibutiken, WebIQ AB

Dallas 1-wire PRO temp sensor 5 meter

Sensor 5 meter X 6mm Affordable 3-wire temperature sensor with the sensor encapsulated in a 6 mm stainless steel casing, the sensors are specially designed for Logger 2020. This type of temperature sensor are very accurate, calibrated in the factory. 5 meter cable Chip: Dallas DS18B20

Reference: 02-006

Brand: Energibutiken, WebIQ AB

Dallas 1-wire PRO tube surface sensor

Tube surface Sensor, affordable 3-wire temperature sensor with the sensor encapsulated in a 14 mm polished "prism" aluminium casing, the sensors are specially adapted to Logger 2020.  This type of temperature sensor are very accurate, calibrated in the factory. Chip: Dallas DS18B20

Reference: 02-033

Brand: Energibutiken, WebIQ AB

Hose clamp

Hose clamp for fastening Pipe wrap probe Fits Pipe wrap probe Dallas 1 PRO and PT1000 and PT100 Pipe wrap probe. Takes pipes up to 100 mm diameter.

Reference: 13-001

Brand: Energibutiken, WebIQ AB

Flow Meter Qp 1.5 with Pulse Output

Flow Meter Qp 1.5 Pulse output Flow meter with pulse output for measurment of flow in the range of 30-3000 liters/h with an accuracy better than +-2%.

Reference: 52-183

Brand: Energibutiken, WebIQ AB

LED indicator lamp 230 V

LED INDICATOR, 230V, RED This 230 V LED indicator can be used as a status indicator for compressors, circulation pumps, motors, etc., in combination with our "Light sensor 230 V" is it possible, by Logger 2020's I/O-module A/DMIQ show operating status of the objects the indicator is connected to.